RESEARCH OF FACTORS AFFECTING THE EFFICIENCY OF ROCK BREAKING EQUIPMENT

Authors

J A. Tursunov, Tashkent State Technical University named after Islam Karimov
R U. Jurayev, Navoiy State University of mining and technologies

Abstract

Nowadays 35-40 % of all the drilling works, performed on mining and geological exploration enterprises, are made by air bottom hole cleaning, and the rest 60-65 % are made by flushing liquids on water base. Air drilling and bottom hole cleaning due to low heat conductivity of air generates high temperature at a borehole bottom thus negatively affecting the efficiency of rock destruction tool; while drilling with water based flushing fluids causes efficiency reduction of rock destruction tool due to formation of slurry mode at a borehole bottom. This paper presents the results of the study of the factors negatively affecting the performance of hammers.

First Page

86

Last Page

93

References

1. R.U. Dzhuraev., M.V. Merkulov. “Normalisation of temperature regime of wells during drilling with air blowing”, 2016. 128.
2. L.K. Gorshkov., V.G. Gorelikov. “Temperature regimes of diamond drilling”, 1992. 173.
3. B.B. Kudryashov., A.I. Kirsanov. “Exploration drilling with air”, 1990. 263.
4. N.V. Solovjev., V.F. Chikhotkin., R.K. Bogdanov., A.P. Zakora. “Resource saving technology of diamond drilling in difficult geological conditions”, 1997. 332.
5. R.U. Dzhuraev., M.V. Merkulov. About an opportunity of vortex pipes application at drilling of geological prospecting wells. “Geology and exploration”, 2013. 76.
6. R.U. Dzhuraev., M.V. Merkulov., V.A. Kosyanov., A.M. Limitovsky. Increasing the efficiency of rock destruction tools when drilling wells with air blowing based on the use of a vortex tube. “Mining Journal. Ore and Metals”, 2020. 71.
7. R.U. Dzhuraev., M.V. Merkulov. Experimental study of bottom-hole thermal capacity during drilling exploration wells with air blowing. “Mining information and analytical bulletin”, 2016. 288.
8. R.U. Dzhuraev., M.V. Merkulov. Analysis of drilling wells with air blowing. “Mining information and analytical bulletin”, 2014. 327.
9. M.V. Merkulov., R.U. Djuraev., O.B. Leontyeva., G.Y. Makarova., Y.B. Tarasova. Simulition of thermal power on bottomhole on the bases of experimental studies of drilling tool operation. “International journal of emerging trends in engineering research”, 2020. 4383.
10. R.U. Djuraev., J.B. Toshov. Study of the temperature regime of rock-breaking tools when drilling wells with air cleaning of the bottom face. “International journal of geology, earth environmental sciences”, 2020. 9.
11. L. William. Working guide to drilling equipment and operations. “Gulf professional publishing”, 2010. 602.
12. R.F. Mitchell., S.Z. Miska. Fundamentals of drilling engineering. “Society of petroleum engineers”, 2011. 710.
13. S. Bridges., L.A. Robinson. Practical handbook for drilling fluids processing. “gulf professional publishing”, 2020. 594.
14. T.G. Byrom. Casing and liners for drilling and completion. “Gulf professional publishing is an imprint of elsevier”, 2015. 420.
15. J. Azar., R. Samuel. Drilling engineering. “Penn Well Corp” 2007. 491.
16. W. Renpu. “Advanced well completion engineering”, 2011. 736.

Recommended Citation

Tursunov, J A. and Jurayev, R U. (2022) "RESEARCH OF FACTORS AFFECTING THE EFFICIENCY OF ROCK BREAKING EQUIPMENT," Technical science and innovation: Vol. 2022: Iss. 4, Article 7.
DOI: https://doi.org/10.51346/tstu-01.22.4-77-0205
Available at: https://btstu.researchcommons.org/journal/vol2022/iss4/7