Prospects for using metal-polymer composite structures in the gear manufacturing

Authors

Umid Mamasobirov, Tashkent State Technical University named after Islam KarimovFollow
Shoraxmat Shoobidov, Tashkent State Technical University named after Islam KarimovFollow
A F. Husanboyev, Uzbek Metallurgical Combine Joint Stock Company

Abstract

In this paper, some thermoplastic polymer composites and filler composites for the production of metal-polymer gear transmissions are presented. Efforts have been made to expand the raw material base and identify ways to increase the durability of gears through technological and design measures.

First Page

276

Last Page

281

References

1. AGMA 920-A01. Materials for plastic Gears. “AGMA Information Sheet”. 2000. 40.
2. “Sabic,Electronic resource”. URL:https://www.Sabic.com/en, https:/sfs:sabic.eu/.
3. V.E. Starzhinsky, A.I. Sviridenok, A.T. Kudinov, S.V. Shilko. Metal-polymer gears and transmissions in Belarus: design, technology for assessing properties. “Metalpolymer gears and transmissions in Belarusians: design, technology for assessing properties”. 2000.
4. A.N. Fedyaeva, S.Y. Matyushkov, G.V. Rogovtsev, A.N. Tarasov. Traction electric drive control at the limit of wheel-rail adhesion and suppression of frictional autooscillations. “Publishing house of VNU”. 2011. 31.
5. R. Schreiber. “Optimization of the adhesion coefficient of an electric locomotive of the 12x series”. 2000. 29.
6. S.V. Kikichev. Increasing the efficiency of adhesion activators by improving their adhesion characteristics. “Abstract of the thesis”. 2009.
7. B. Engel. Traction control with high use of adhesion forces. “World railways”. 1999. 39.
8. D.K. Minov. “Improvement of traction properties of electric locomotives and diesel locomotives with electric transmission”. 1965. 267.
9. E.M. Frenkel. To the question of wheel-rail adhesion. “Trans Holder Publishing”. 1953.
10. H. Zhua, M. Salyani, R.D. Fox. A portable scanning system for evaluation of spray deposit distribution. “Journal of computers and electronics in agriculture”. 2011. 38.
11. M. Salyani, M., R.D. Fox. “Evaluation of spray quality by oil and water sensitive papers”. 2011. 37.
12. K.M. Sundaram, P.D. Groot, A. Sundaram. “Permethrin deposits and airborne concentrations downwind from a single swath application using a back pack mist blower”. 1987. 171.
13. G. Heidarinejad, M. Bozorgmehr. Modelling of indirect evaporative air coolers. “International journal of heat and mass transfer”. 1993. 17.
14. G.Q. Qiu, S.B. Riffat. Novel design and modelling of an evaporative cooling system for buildings. “International journal of energy research”. 2006. 985.
15. L.A. Andrienko, B.A. Baikov, I.K Ganulich. Under the editorship of O.A. Rykhovsky Machine parts [Detail of machines]: Proc. for universities. “Publishing house of MSTU”. 2002. 544.

Recommended Citation

Mamasobirov, Umid; Shoobidov, Shoraxmat; and Husanboyev, A F. (2022) "Prospects for using metal-polymer composite structures in the gear manufacturing," Technical science and innovation: Vol. 2022: Iss. 1, Article 10.
DOI: https://doi.org/10.51346/tstu-01.22.1-77-0165
Available at: https://btstu.researchcommons.org/journal/vol2022/iss1/10